Waterway 19" TWM Sand Filter System

Availability: In stock

Waterway 19" TWM Sand Filter System for new or old above ground pools. 19" sand tank, 2 sq.ft. filtering area, 1.0 hp pump, 115V, 42 GPM, Water turnover rate is 20,160 gallons in 8 hours. Everything included to get your pool up and running fast. Easy installation with few pieces to assemble. Kit includes pump, filter body, multi-port valve, mounting platform base, hoses, clamps, fittings and all necessary hardware.


Typical UPS delivery time is 3-5 business days. Package weight 60 lbs.

Price:
$400.00
OR
Description

Details

Waterway TWM sand filters systems for new or old above ground pools. 19" tank, 1.0 hp pump, 7 position multi-port valve, 115V, 42 GPM  Water turnover rate is 20,160 gallons in 8 hours. Large capacity filter body to capture dirt and debris. Large size means less cleaning and longer filtering cycles. Designed specifically for the rigors of above-ground filtration and engineered for easy use with flexible or rigid PVC plumbing. Everything included to get your pool up and running fast. Easy installation with few pieces to assemble. Kit includes pump, filter body mounting platform base, hoses, clamps, fittings and all necessary hardware.

Typical UPS delivery time is 3-5 business days. 

How A Sand Filter Works - In swimming pools, water is pumped into a large tank that is filled with #20 Silica sand. As the water enters the top, a diffuser sprays the water out evenly across the top of the sand bed, ensuring perfect distribution.This water settles down through the sand bed entrapping the debris and returns back to the swimming pool filtered.
As the amount of debris, hair, bugs, algae, oils and more increases, the sand starts to become clogged. This restriction is noticeable on the pressure gauge located on the filter tank. The increase in tank pressure indicates the the filter is in need of cleaning or back-washing. The back-washing process rinse the sand of impurities and allows the water to flow freely again. The ease of flow lowers the pressure within the tank and the process starts over again. Keep in mind that the more a sand filter plugs up, the finer the particulates that are captured so its ok to let the pressure climb some, and not backwash too frequently. Normal operating pressure varies by filter but typically it runs between 10-20 psi. When the pressure within the tank increases by about 10 psi or more, back-washing is needed. Allowing too much pressure to build in the tank can damage the pump and possibly the filter tank.

Cleaning The Sand Filter - To clean or back-wash a sand filter, cut the power to the pump and set the control valve to backwash, then turn the pump back on. The filter will now rinse the sand within the filter tank, sending dirty water out the back-wash port. This water can be directed away from lawns, flowers or gardens as it is chlorinated and may cause damage to plant life. This is done simply by using a backwash hose attached to the back-wash port. Continue to backwash for about two minutes or until the water runs clear through the sight glass if equipped. Shut the pump off again and return the control valve to filter mode.

Sand Filter Efficiency - Sand will filter down to about 20 microns. This is small and enough to capture most all impurities in your pool water. Sand filters will becomes clogged and cakes up over time due to the accumulation of oils, lotions hair and other debris. Even with regimented maintenance the sand within the filter tank should be replaced every 3-5 years for best results.

Changing The Sand - To empty or change the sand you disconnect the hoses or PVC piping from the filter tank. Next remove the control from the tank top and begin the manual process of scooping the sand out of the tank. Some pool professionals and pool owners turn the tank on it's side and use a water hose to spray it out of the tank. Once the sand is removed you can replace it with #20 Silica sand in the required amount dictated be the manufacturer. Use care to fill the tank and keep the sand from entering the pipe in the center. Once full of sand, replace the control valve and tighten the band. Reconnect the hoses or piping and you should be set to operate the filter once again.

Additional Info

Additional Information

  • Country of Manufacture
  • Brand
    Waterway
  • Filter Media Type
    Sand
  • Filter Line
    TWM
  • Pipe Size
    No
  • Filter Includes
    Complete Filter Systems
  • Horsepower
    1.0 HP
Reviews

You're reviewing: Waterway 19" TWM Sand Filter System

Documents